View CC4532680KL_4598482.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SPECIFICATION FOR APPROVAL
REF : 20071102-D PROD. NAME ABC'S DWG NO. CC4532L- PAGE: 1
WOUND CHIP INDUCTOR
ABC'S ITEM NO.
CONFIGURATION & DIMENSIONS
A B C 4.20.2 F : : : 4.50.3 3.20.2 3.20.2 1.2 m/m m/m m/m m/m m/m
330K
Marking
Inductance code
E:
: 1.0 +0.3 -0
C
F A
F
E B
1.5 2.2 1.5
PCB Pattern
SCHEMATIC DIAGRAM
d a
MATERIALS
aCoreFerrite DR core bWire Enamelled copper wire (class H) cTerminalCu/Sn dEncapsulateEpoxy novolac molding compound eRemarkProducts comply with RoHS' requirements
1.6
c
b
Reflow profile Peak Temp250 max. Max time above 245 20~40sec max. Max time above 217 60~150sec max. 200~250 Average Ramp-up Rate3/second max.
Temperatu re Rising Area Preheat Area 1 50 ~ 200 / 60 ~ 180 sec Reflow Area Forced Cooling Area 6 / secon d max.
P eak Temperature 250
GENERAL SPECIFICATION
aTemp. rise 20 max. bAmbient temp.100 max. cStorage temp.-40 ----+125 dOperating temp.-40----+125 eTerminal pull strength1.5 kg min. fRated currentCurrent cause inductance drop within 10% gResistance to solder heat260.10 secs. hResistance to solventPer MIL-STD-202F AR-001A
Temperature ( )
250 245 217 200 150 100 50
2 0~40sec
6 0~1 50sec
0
50
100
150 Time ( seconds )
200
250
SPECIFICATION FOR APPROVAL
REF : 20071102-D PROD. NAME ABC'S DWG NO. CC4532L- PAGE: 2
WOUND CHIP INDUCTOR
ABC'S ITEM NO.
ELECTRICAL CHARACTERISTICS
DWG NO. CC45321R0KL - CC45321R2KL - CC45321R5KL - CC45321R8KL - CC45322R2KL - CC45322R7KL - CC45323R3KL - CC45323R9KL - CC45324R7KL - CC45325R6KL - CC45326R8KL - CC45328R2KL - CC4532100KL - CC4532120KL - CC4532150KL - CC4532180KL - CC4532220KL - CC4532270KL - CC4532330KL - CC4532390KL - CC4532470KL - CC4532560KL - CC4532680KL - CC4532820KL - CC4532101KL - CC4532121KL - CC4532151KL - CC4532181KL - CC4532221KL - CC4532271KL - CC4532331KL - CC4532391KL - CC4532471KL - CC4532561KL - CC4532681KL - 1). Inductance ( H ) 1.00 1.20 1.50 1.80 2.20 2.70 3.30 3.90 4.70 5.60 6.80 8.20 10.00 12.00 15.00 18.00 22.00 27.00 33.00 39.00 47.00 56.00 68.00 82.00 100.00 120.00 150.00 180.00 220.00 270.00 330.00 390.00 470.00 560.00 680.00 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% Q min. 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 20 20 20 20 20 20 20 20 20 20 20 Test Freq. ( MHz ) 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 SRF ( MHz ) min. 180.0 160.0 130.0 100.0 80.0 60.0 45.0 40.0 35.0 30.0 28.0 25.0 22.0 21.0 20.0 19.0 18.0 16.0 14.0 12.0 11.5 11.0 10.0 9.0 8.0 7.5 7.0 6.5 5.5 5.0 4.0 3.0 3.0 3.0 2.5 RDC () max. 0.11 0.12 0.15 0.16 0.18 0.20 0.22 0.24 0.27 0.30 0.35 0.40 0.50 0.60 0.70 0.80 0.90 1.20 1.40 1.60 1.90 2.20 2.60 3.50 4.00 4.50 6.50 7.50 9.00 11.00 13.00 14.00 16.00 18.00 22.80 IDC ( mA ) max. 1050 1000 950 900 850 800 750 700 650 650 600 600 550 500 450 400 370 330 300 280 260 240 220 200 180 160 140 120 120 100 90 85 75 70 65
Packaging information... ABulk 2)."- ":Reference code
BTaping Reel
AR-001A
SPECIFICATION FOR APPROVAL
REF : 20071102-D PROD. NAME ABC'S DWG NO. CC4532L- PAGE: 3
WOUND CHIP INDUCTOR
ABC'S ITEM NO.
CURVE @ Inductance VS. DC Superposition Characteristics
10 7 5 3 2
2
101K
330K
Inductance (uH)
10 1 7 5 3 2 10 0 7 5 3 2 2R7K
1R0J
10 1
2
3
5 7 10 2
2
3
5 7 10 3
2
3
5 7 10 3
DC Current (mA)
@ Q VS. Frequency Response
100 90 80 70 60 Q 50 40 30 20 10 10
-1
101K 331K 330K 2R7K 100K 1R0M
2
4
6
8 10
0
2
4
6
8 10
1
2
4
Frequency (MHz) AR-001A
SPECIFICATION FOR APPROVAL
REF : 20071102-D PROD. NAME ABC'S DWG NO. CC4532L- PAGE: 4
WOUND CHIP INDUCTOR
ABC'S ITEM NO.
PACKAGING INFORMATION
( 1 ) Configuration T
Cover tape
2.00.5 A B N C C
G
D
Embossed carrier
Carrier tape width : D P:8 m/m End 4 m/m Start
330K
330K
330K
Leader no component 200 m/m min.
330K
Components User direction of feed
Trailer no component 400 m/m min.
There is no differentiation or directions of polarity ( marking ) in the packaging method. ( 2 ) Dimensions Style 07 - 12 13 - 12 A 178 330 B 210.8 210.8 C 13 130.5 D 12 12 G 14 14 +0 +0 N 50 50 -0 -0 Unit:m/m T 16.5 18.4
( 3 ) Q'TY & G.W. Per package Inner : Reel Series
CC4532 CC4532
Q'TY (pcs) G.W. (gw) Style Q'TY (pcs)
Outer : Carton
G.W. (Kg) Size (cm)
500 2000
140 550
07 - 12 13 - 12
20,000 18,000
8.00 6.80
41 x 39 x 22 41 x 39 x 22
AR-001A
SPECIFICATION FOR APPROVAL
REF : 20071102-D PROD. NAME ABC'S DWG NO. CC4532L- PAGE: 5
WOUND CHIP INDUCTOR
ABC'S ITEM NO.
DWGING NUMBER EXPRESSION
C
C
4
5
3
2 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code
Appendix code 1Product Classification LLead Free Standard products comply with RoHS' requirements 1 ~ 9Lead Free Special products comply with RoHS' requirements
Appendix code 2Package Information
Code A B C Bag
Inner package
Inner package Q'TY 500 500 2000 pcs pcs pcs
Remark
T / R ( Reel package ) T / R ( Reel package )
AR-001A
SPECIFICATION FOR APPROVAL
REF : 20071102-D PROD. NAME PAGE: 6 ABC'S DWG NO. ABC'S ITEM NO. CC4532L-
WOUND CHIP INDUCTOR
RELIABILITY TEST
Test item Specification Test condition / Test method
Electrical performance test Inductance L Q Self resonance frequency SRF DC Resistance RDC Rated current IDC HP4194A with HP-16034E test fixture Refer to standard electrical characteristic list HP4291A with HP-16093A test fixture CH-502AC
Applied the current to coilsThe
Temperature rise test
20 max. After testInductors shall be no evidence of electrical and mechanical damage After tsetInductors shall be no evidence of electrical and mechanical damage 1000 M min
Inductance change shall be less than 10% to initial value & temperature rise shall not be more than 20 1Applied the allowed DC current for 10 minutes 2Temperature measure by digital surface thermometer Applied 2 times of rated allowed DC current to inductor for a period of 5 minutes AC voltage of 1000VAC applied between inductors terminal and coating for 5 seconds 100 VDC applied between inductor terminal and coating
Over load test
Withstanding voltage test Insulation resistance test
Mechanical performance test Vibration test ( Low frequency ) 1Inductors shall be no evidence of electrical and mechanical damage 2Inductance shall not change more than5% 3Q Shall not change more than 20% 1Amplitude1.5 m/m 2Frequency10 -- 55 -- 10 Hz / 1min. 3DirectionXYZ 4Duration2 hrs / XYZ Inductors shall be dropped 10 times from a height of 1m onto 3cm wooden board Temp2605 Time101.0 sec.
Shock test Resistance to soldering heat
AR-001A
SPECIFICATION FOR APPROVAL
REF : 20071102-D PROD. NAME PAGE: 7 ABC'S DWG NO. ABC'S ITEM NO. CC4532L-
WOUND CHIP INDUCTOR
Terminal strength-pull test
Terminal shall not be loosened or ruptured
A 0.5kg load shall be applied to both Terminals in the axis direction for 1 minute After fluxingInductor shall be dipped in a melted solder bath at 2405 for 5 seconds
Solderability test
The terminal shall be at least 90% covered with solder There shall be no case deformation change in appearance or obliteration of marking
Resistance to solvent test
MIL-STD-202FMethod 215D
Climatic test Temperature characteristic Humidity test Cold test 1Inductors shall be no evidence of electrical and mechanical damage 2Inductance shall not change more than 10% 3Q shall not change more than 20% -40 -- +125 1Temp402 2R.H.90 -- 95% 3Time962 hours 1Temp-252 2Time962 hours Room temp 15 mins Room temp 15 mins
Thermal shock test
-402 30 mins +1252 30 mins
Dry heat test High temperature load life test
Humidity load life
There shall be no evidence of short or open circuiting
Total5 cycles 1Temp852 2Time962 hours 1Temp852 2Time100012 hours 3LoadAllowed DC current 1Temp402 2R.H.90 -- 95% 3Time100012 hours 4LoadAllowed DC current
Note Unless otherwise specified , Allow the specimen to stand at room temperature for 1 hour or more but not more than 2 hours , Measure the electrical and mechanical performances
AR-001A
SPECIFICATION FOR APPROVAL
REF : 20071102-D PROD. NAME PAGE: 8 ABC'S DWG NO. ABC'S ITEM NO. CC4532L-
WOUND CHIP INDUCTOR
UL CARD
OBMW2 Magnet Wire-Comporent
August 27, 1999 E143312
ELEKTRISOLA (MALAYSLA) SDN BHD IALAN DAMN SATU IANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA
Coating Type Mtl Dsg
Estersol 160 Amldester 200 Polysol-N 155 Polysol 155 Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180
Mark Dsg
E180 A200 PN155 P155 Pg155 Pp155,Gp155 P160 P180 P170 or G170 PN180
BC
Polyesterimide (solderable) Polyesterimide Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane
OC
____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon
ANSI Typ
MW-77 MW-74 MW-80, MW-28 MW-79, MW-79 MW-79 MW-79 MW-79 MW-79 MW-79 ____
Temp Class
180 200 155, 100 155, 130 130 155 155 155 156 180
MarkingDompany name/nateriel designation or marked designation and factory identification on package ok reel
See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc.
OMFZ2
March 4, 1994 E59481 (S)
BM-21 BM-22 BM-23 EME-1100 EME-1200 EME-5961C
ALL ALL ALL BK BK BK BK BK BK
0.79 0.79 0.79 0.84 6.4 0.84 6.4 0.3 3.1
94HB 94HB 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0
50 50 50 130 130 130 130 130 130
50 50 50 130 130 130 130 130 130
50 50 50 130 130 130 130 130 130
__________________
Reports: January 19, 1988: January 19, 1988: January 19, 1988: June 2, 1988; June 2, 1998; June 2, 1988.
R
AR-001A

▲Up To Search▲

Price & Availability of CC4532680KL

	To Download CC4532680KL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .